Stick Clip Tricks for Sport Climbers. "Damn, but this wall is steep steep steep," I mutter to myself. I'm mid-lower from a popular sport route and, increasingly, I'm experiencing technical difficulties cleaning the draws. I'm tethered to the rope with a quickdraw, but I'm pumped from the route and the lower I get, the harder it is to pull myself into the wall, unweight the rope and pluck the draws free. Soon though, after much work, the last draw left standing is the first on the route. Stick clipped by most people who climb this line, this particular bolt was placed high specifically to minimize the number of bolts on the route. The FA intended for people to use the clip. And indeed, without a stick clip, if one blows the lower moves, the result will be messy as he or she crashes into a either a chunk of talus or a dead tree trunk, then tumbles another 10 meters to the base of a lower tier cliff. The unlucky belayer will follow unceremoniously to land in a clump atop the climber. Trez Wiley Coyote. So, the stick clip provided me an easy and safe solution, right up until now. I don't want to unclip the first bolt and swing out, because there are other trees waiting hungrily. And I sure ain't gonna boulder back up to clean it, for the reasons mentioned above.
What's a poor, technically inept sport climber to do? Bring out the stick clip again, of course. Many climbers use a clip to place the first draw, but many more are unaware that the standard, home-made aligator-clamp stick clip also makes a fine tool for removing draws and for clipping the rope into already-hung draws. Here's how. First, you need a standard, home-made clip. Most people make them with an extending painters' pole, and aligator clamp and a couple of hose clamps. If you don't know how to do that, try a search.
In the above shot, my home-made stick clip is being used for standard light duty -- hanging a first draw. Note that the the clamp is holding both the spine and the gate of the biner. With a firm enough clamp, even wire gates are no problem. All one has to do is place the draw in the clamp, place the rope in the draw and then reach up and clip. Once the nose of the biner clears the bolt hanger, just yank the stick down. The clamp will release the draw and the gate will shut. If, for some reason, you pull out too early, just slap the spine of the biner with the stick. It'll go right in.
(Insert sex joke here.)
You: But j_ung, everybody knows that trick. What's the point of this post, loser?
Me: Shut up, fool!
CLIPPING THE ROPE INTO A PRE-HUNG DRAW
That's the easy part. Here's where we get a little (for sport climbers, anyway) technical. Let's say you're out swapping leads with your partner and the dehydrated idiot accidentally pulls the rope completely down without leaving you the first clip. No problemo, but it'll take a little rigging. You need another biner. I used a BD Neutrino, but I gotta tell you, bigger biners work better. Trust me on this and save yourself some trouble. Slide the biner up one of the legs of the clamp...
...bring it all the way up and over the top and then clamp its nose, like so:
Notice that the clamp itself and the basket of the biner form a small loop. That's what you need. In fact, the above configuration is the basis for both of the tricks I'm about to show you. From now on, I'm going to call it The Glory Hole. Cram a small bight of rope through The Glory Hole and cinch the biner tightly into the clamp so it holds the bight firmly. The bight should be just big enough to admit a hanging quickdraw, like so:
Now, raise the clip to the draw so that the rope is on the gate-side of the draw's bottom biner.
Give the rope a little pull. That's it. Slow and steady.
Voila! You got it!
REMOVING QUICKDRAWS
Warning: This is not easy. It takes practice. Seriously. In my opening monologue I illustrated the problem that arises when it's difficult or even dangerous to clean the bottom draw while lowering. Bust a stick move again! Sport climbers beware: things are about to get very technical... First, build yourself The Glory Hole. Cram another bight of rope through The Glory Hole, just like when you clipped the draw last time. This time, however, bring the loop all the way up to the draw's top biner, again so that the bight of rope is on the biner's gate side.
Give the bight a slow, steady pull to open the biner's gate...
That's it. Now, here's where the practice comes in. The next step is very tricky. The rope is going to want to slide up the gate and into the biner. The only way to keep it from doing that is to pull the rope down tightly to hold the gate open firmly. But also... hold the clip up. That's the tricky part. Practice practice practice... Once you've learned the correct tension between pulling the rope and down and pushing the stick clip up, it's an easy matter to swing the stick sideways a bit and gently lift the biner out of the bolt hanger, like so...
Again, don't expect to get this right on the first try. The good news is that if it doesn't work, you gan just pull the rope and clip down and start again. I think that, as you practice, you'll notice a few things. Keylock biners are easier to unclip than standard hook-and-pin biners. Some shapes work better than others for making The Glory Hole. Blah blah blah... There, now all you technically inept (just kidding!) sport climbers have a gear trick to call your very own.
What's a poor, technically inept sport climber to do? Bring out the stick clip again, of course. Many climbers use a clip to place the first draw, but many more are unaware that the standard, home-made aligator-clamp stick clip also makes a fine tool for removing draws and for clipping the rope into already-hung draws. Here's how. First, you need a standard, home-made clip. Most people make them with an extending painters' pole, and aligator clamp and a couple of hose clamps. If you don't know how to do that, try a search.
In the above shot, my home-made stick clip is being used for standard light duty -- hanging a first draw. Note that the the clamp is holding both the spine and the gate of the biner. With a firm enough clamp, even wire gates are no problem. All one has to do is place the draw in the clamp, place the rope in the draw and then reach up and clip. Once the nose of the biner clears the bolt hanger, just yank the stick down. The clamp will release the draw and the gate will shut. If, for some reason, you pull out too early, just slap the spine of the biner with the stick. It'll go right in.
(Insert sex joke here.)
You: But j_ung, everybody knows that trick. What's the point of this post, loser?
Me: Shut up, fool!
CLIPPING THE ROPE INTO A PRE-HUNG DRAW
That's the easy part. Here's where we get a little (for sport climbers, anyway) technical. Let's say you're out swapping leads with your partner and the dehydrated idiot accidentally pulls the rope completely down without leaving you the first clip. No problemo, but it'll take a little rigging. You need another biner. I used a BD Neutrino, but I gotta tell you, bigger biners work better. Trust me on this and save yourself some trouble. Slide the biner up one of the legs of the clamp...
...bring it all the way up and over the top and then clamp its nose, like so:Notice that the clamp itself and the basket of the biner form a small loop. That's what you need. In fact, the above configuration is the basis for both of the tricks I'm about to show you. From now on, I'm going to call it The Glory Hole. Cram a small bight of rope through The Glory Hole and cinch the biner tightly into the clamp so it holds the bight firmly. The bight should be just big enough to admit a hanging quickdraw, like so:
Now, raise the clip to the draw so that the rope is on the gate-side of the draw's bottom biner.
Give the rope a little pull. That's it. Slow and steady.
Voila! You got it!
REMOVING QUICKDRAWS
Warning: This is not easy. It takes practice. Seriously. In my opening monologue I illustrated the problem that arises when it's difficult or even dangerous to clean the bottom draw while lowering. Bust a stick move again! Sport climbers beware: things are about to get very technical... First, build yourself The Glory Hole. Cram another bight of rope through The Glory Hole, just like when you clipped the draw last time. This time, however, bring the loop all the way up to the draw's top biner, again so that the bight of rope is on the biner's gate side.
Give the bight a slow, steady pull to open the biner's gate...
That's it. Now, here's where the practice comes in. The next step is very tricky. The rope is going to want to slide up the gate and into the biner. The only way to keep it from doing that is to pull the rope down tightly to hold the gate open firmly. But also... hold the clip up. That's the tricky part. Practice practice practice... Once you've learned the correct tension between pulling the rope and down and pushing the stick clip up, it's an easy matter to swing the stick sideways a bit and gently lift the biner out of the bolt hanger, like so...
Again, don't expect to get this right on the first try. The good news is that if it doesn't work, you gan just pull the rope and clip down and start again. I think that, as you practice, you'll notice a few things. Keylock biners are easier to unclip than standard hook-and-pin biners. Some shapes work better than others for making The Glory Hole. Blah blah blah... There, now all you technically inept (just kidding!) sport climbers have a gear trick to call your very own.
Related Post:
Mp3 Download
5 komentar:
mampir di t4 sahabat sambil bersedekah 1 di GA , jgn lupa mampir ke rumah saya sambil bersedekah juga 1 ya, mari qt budayakan saling bersedekah
ha,, this's my old hobby .. i haven't more power now.. ^_^
boleh belajar
www.apitaik.co.cc
nice tips
helloooo....
Post a Comment